March 2026
February 2026
January 2026
December 2025
November 2025
September 2023
August 2023
- 08-28 3h Finished mounting the vertical stabilizer
- 08-27 4h Started mounting the vertical stabilizer
- 08-26 4h Finished mounting the horizontal stabilizer
- 08-25 3h Started mounting the horizontal stabilizer
- 08-24 5h Finishing the service bulletin SB-00036
- 08-23 1.5h Priming various parts
- 08-22 1.5h Service bulletin SB-00036 REV 3
- 08-20 2h Finished riveting aft skins
- 08-19 1.5h Installing the nutplates
- 08-17 1.5h Baggage bulkhead panels
- 08-16 1.5h Working on the OP-60 ADAHRS bracket
- 08-15 2h Working on the OP-43 access panels
- 08-13 1h Riveting the aft fuselage skins
July 2023
- 07-30 1h Fabricating central tunnel cover
- 07-29 2h Priming aft skins
- 07-25 1h Installing Click Bond mounts
- 07-23 3h Worked on the flaps actuator
- 07-22 4h Installed the flaps actuator
- 07-21 3h Riveted the right baggage floor
- 07-20 3h Riveted the gussets and the left baggage floor
- 07-19 1h Priming the baggage floors
- 07-17 3h Riveting the floors and the gussets
- 07-16 2h A bit of priming work
- 07-13 2h Drilling the top aft skins
- 07-09 2.5h Riveting the external steps
- 07-09 2.5h Drilling the J-stiffeners and the ribs
- 07-01 5h Fitting the aft top skins
June 2023
- 06-30 2h Riveting the canopy decks, F-709 bulkhead and the shoulder harness anchors
- 06-29 2h Riveting the aft deck and the rudder brace
- 06-28 1.5h Priming the canopy decks and the aft deck
- 06-27 2.5h The bellcrank channel and the remaining gusset
- 06-26 2.5h Drilling various gussets
- 06-25 4h Rudder brace, spacers, and fuselage gussets
- 06-24 1.5h Rolled over the canoe
- 06-23 1.5h Fabricating spacers for the step tubes
- 06-22 1.5h Riveting the right baggage bulkheads
- 06-21 2.5h Few more parts are primed
- 06-18 8h Fuselage almost riveted
April 2023
- 04-29 3h Sealing the firewall
- 04-22 3h Three little tasks
- 04-17 4h Assemling the fuselage
- 04-16 6h Installing the left skin
- 04-12 2.5h New right longeron
- 04-11 1.5h Countersinking the F-704-H side plates
- 04-08 4h Riveted F-704 to the central section
- 04-07 2h Primed some parts
- 04-05 3h Assorted work
- 04-04 3h Countersinking the longerons
- 04-02 2h Countersinking and deburring
- 04-01 3h The cowling hinges
March 2023
- 03-25 3h The reinforcement angles
- 03-23 2h The left F-7101 and countersinks
- 03-21 3h The right F-7101 and drilling the floor
- 03-19 1.5h The left external step and the floor stiffeners
- 03-08 2h Fitting the rudder pedals block
- 03-07 4h Fabricating the rudder pedals bearings
- 03-04 3h Drilling the floor stiffeners
- 03-03 1h Drilling the lower longeron
- 03-02 2.5h Baggage area framing
- 03-01 1.5h Ruining some parts
February 2023
- 02-28 2h Fitting the left F-684 gusset
- 02-27 2h Fitting the right F-684 gusset
- 02-26 2h Drilling the bolt holes in the lower longerons
- 02-25 4h Finishing fitting the stiffeners
- 02-24 3h Fitting the right auxiliary longeron
- 02-23 2.5h Fitting the left auxiliary longeron
- 02-22 3h Fitting the firewall
- 02-20 1h Fabricating the F-904-L straps
- 02-18 1.5h Drilled the left step to the skin
- 02-17 4h Finishing the right step
- 02-16 2.5h Fitting the right external step
- 02-15 1.5h Continued drilling the fuselage
- 02-14 3h Drilling the longerons
- 02-13 2h Fitting the other skin
- 02-12 3h Longerons and the side skin
- 02-11 4h Joining the fuselage
- 02-01 2h Installing the aileron trim and the crotch strap brackets
January 2023
- 01-31 1h Priming the brackets
- 01-29 3h Working on an aileron trim
- 01-28 2h Finished riveting the aft section
- 01-21 2h Few more F-711 rivets
- 01-19 1h Few more aft fuselage rivets
- 01-16 2h Riveting the remaining fuselage aft rivets
- 01-15 4h Fitting the tail spring mount
- 01-14 2h Preparing for the fuselage join
- 01-13 4h Drilling the new seat ribs
- 01-12 3h Removing the crotch strap brackets
- 01-07 30m Just a minor item
- 01-06 1h Some setbacks
- 01-05 4h Drilling the ribs and the tailspring
- 01-04 3h Finishing the longerons, continuing the center section
- 01-03 5h Bending the longerons
- 01-01 4h Riveting the ribs and fitting the control column
December 2022
- 12-31 3h Priming the parts of the center section
- 12-30 3h Making spacers for F-704
- 12-28 1.5h Riveted F-704
- 12-27 3h Fitting the tailwheel spring mount
- 12-26 3h Fabricating the web stiffeners
- 12-25 1h Preparing for riveting
- 12-24 2h Wing alignment pins
- 12-23 4h Optional lightening and cover ribs
- 12-22 5h Started working on F-704 bulkhead
November 2022
October 2022
- 10-30 2.5h Riveting the center section
- 10-25 2h Repairing some flanges
- 10-24 4h Riveting ribs to the bulkhead
- 10-23 2h Installing the nutplates and dimpling the skin
- 10-22 6h Priming the center section ribs
- 10-20 3h Fitting new ribs and priming the skin
- 10-19 1.5h More deburring
- 10-18 2h Deburring the center section parts
- 10-16 2h Fluting the F-715 seat ribs and disassembly
- 10-15 5h Drilling the center section and F-623 ribs
- 10-12 3h Drilling the crotch strap brackets and clecoed the center section
- 10-11 3h Fluting the seat ribs
- 10-10 3h Working on seat ribs
- 10-09 30m Modifying the seat ribs
- 10-08 2h Finished riveting aft fuselage
- 10-07 1h Cutting the holes for the tailwheel mount
- 10-06 1h More of the aft fuselage riveting
- 10-05 1h Continuing riveting the aft fuselage
- 10-04 4h Dimpling and beginning of an aft fuselage riveting
- 10-03 3h Priming J-stiffeners
- 10-02 1h Minor things
- 10-01 3h Primed the aft fuselage skins
September 2022
- 09-30 1.5h Finished deburring aft fuselage parts
- 09-29 2h Started deburring aft fuselage parts
- 09-28 3h Drilling the aft fuselage and rudder cable fairings
- 09-26 1h More tiny tasks
- 09-25 3h Various small tasks
- 09-24 4h Drilling the J-channels
- 09-22 1h Priming the F-711 parts
- 09-21 3h Fabricating F-711B
- 09-17 1h Modifying the forming block
- 09-16 3h Forming block for the F-711B
- 09-14 2h Fitting the F-711 bulkhead
- 09-13 2h Starting the aft fuselage assembly
- 09-12 4h Riveting the F706 bulkhead
- 09-11 3h Priming the F706 parts
- 09-09 3h Deburring the bulkheads
- 09-08 2h F-706 bulkhead parts
- 09-07 2h Wiring holes in F-706, F-707, F-708
- 09-06 2h F711 and F712 bulkheads
- 09-05 2h Various aft bulkheads
- 09-04 1h F-710B angle
- 09-03 6h Riveting F705 together
- 09-02 2h Priming the F705 bulkhead parts
- 09-01 4h Riveting firewall together
August 2022
- 08-31 2h Priming the firewall parts
- 08-29 1h Seat stop plate
- 08-27 4h Dimpling and counter-sinking firewall parts
- 08-25 1.5h Making a new firewall angle
- 08-23 3h Drilling the remaining F-705 bulkhead parts
- 08-22 4h More work on the F-705 bulkhead
- 08-19 3h F-705 bulkhead
- 08-18 5h Drilling firewall components
- 08-17 4h Firewall bulkhead
- 08-16 8h Fuselage inventory
